Pro Controll EZ Mount II

Product Description

Looking for a rust‑proof bow‑mount bracket for a jon or utility boat? Pro Controll EZ Mount II is a composite, clamp‑on solution that converts hand‑control transom trolling motors for bow or side mounting—great for 12V setups in wind and tight cover.

Pro Controll EZ Mount II is a universal, rust‑proof composite clamp‑on bracket that converts a hand‑controlled transom‑mount trolling motor for bow or side mounting in minutes. Its adjustable underside bracket hugs angled rails and curved hulls for a stable setup on many small boats.

Extended Product Description

Traditional aluminum brackets can corrode and add weight. EZ Mount II solves both with a lightweight composite body and an adjustable outside support for added stability. After clamping, rotate the motor head 180° so that forward on the tiller pulls from the bow for precise positioning in wind and current.

What Problem Does the Pro Controll EZ Mount II Solve?

If wind keeps pushing your stern around, you’re fighting the boat instead of fishing. Forward pull from the bow delivers tighter turns and better control—without the cost or drilling of a dedicated bow‑mount motor. EZ Mount II’s composite build resists corrosion season after season.

Dedicated bow motors cost more and require permanent deck work. EZ Mount II gives you the bow‑control advantages using the motor you already own—with no drilling and no corrosion worries.

Specs

• Material: Fiberglass‑reinforced nylon body; stainless/zinc‑plated hardware
• Mounting: No‑drill clamp with adjustable underside bracket
• Fit: Gunnels/top rails up to ~3″ wide (allow space for interior clamp screws)
• Motors: Hand‑control, transom‑mount electric trolling motors
• Thrust: 30–55 lb typical (verify rail strength)
• Placement: Bow or sides; re‑check tightness in chop

What Next?

Ready for better bow control—without drilling or rust? Add Pro Controll EZ Mount II to your cart and upgrade your small‑boat handling today.

Pro Controll EZ Mount II — Frequently Asked Questions (FAQ)

Find quick answers about the EZ Mount II before you buy

The Pro Controll EZ Mount II is our upgraded, universal bracket that lets you mount a hand‑controlled transom trolling motor to the bow or side of many small boats—without drilling holes. Its adjustable underside bracket hugs your hull for a secure fit, and the corrosion‑resistant composite build keeps you fishing longer in harsh conditions.

1. 🔧 What is the Pro Controll EZ Mount II?

EZ Mount II is a universal, clamp‑on bracket that converts a hand‑controlled, transom‑mount trolling motor for bow or side mounting. It adds an adjustable underside bracket for better hull contact and a corrosion‑resistant composite construction.

2. 🆚 How is EZ Mount II different from the original EZ Mount?

It features an adjustable lower (outside) bracket to match angled or curved hulls, a lighter, corrosion-resistant fiberglass-reinforced nylon body, and improved flexibility for placement (bow or sides) while retaining the no-drill clamp system.

3. 📏 What gunnel (top rail) sizes does EZ Mount II fit?

It works with top rails approximately 1″ to 3″ wide. As with any clamp‑based mount, you’ll need sufficient flat rail area for a confident grip and room inside the boat for the interior clamp screws.

4. ⚡ Which trolling motors are compatible?

Most hand‑controlled, transom‑mount electric trolling motors (e.g., Minn Kota Endura/Traxxis, MotorGuide R‑series, Newport Vessels NV). It is not intended for foot‑controlled or GPS‑steer bow motors.

5. 🧰 What tools are needed for installation?

Basic hand tools: a small hammer and punch to remove the original hinge pin, and standard hand tightening for the clamp screws and skewer lever. Many installs can be completed in minutes.

6. 🧭 How do I orient the motor when moving it to the bow?

After mounting, rotate the motor head 180° so the tiller handle and propeller face the same direction. This ensures that the tiller pulls the boat forward from the bow.

7. ⚙️ How stable is EZ Mount II on the water?

The clamp screws hold the bracket to the inner rail while the adjustable lower bracket presses against the outer hull for multi‑point contact. Tighten by hand firmly (do not over‑tighten) and recheck periodically, especially in chop or heavy wind.

8. 🌊 Is it corrosion‑resistant for saltwater use?

Yes—its fiberglass‑reinforced nylon body and stainless/zinc‑plated hardware resist corrosion. Rinse with freshwater after salt or brackish use and periodically inspect hardware.

9. ⚖️ What motors and thrust levels work best?

For most small boats, 30–55 lb thrust hand‑tiller motors pair well. On heavier boats or in rough water, verify that your rail and clamp points can handle the added loads and re‑check tightness more often.

10. 🧱 Will it work on V‑hull or angled bows?

Yes, the adjustable underside bracket is designed to match hull angles. For extreme bevels or unusually shaped rails, a small shim plate may help create a vertical face for the motor bracket.

11. 🛡️ Will using EZ Mount II affect my boat or motor warranty?

Because it typically avoids drilling or permanent modification, many users have no issues. Always check your specific boat/motor warranty and follow safe‑use guidelines.

12. ⏱ How quickly can I install and remove it?

Once your motor’s bracket has been swapped, clamping to the rail is fast—often just a few minutes. That portability also makes it easy to transfer between boats or remove for storage.

Ready to upgrade your boat control? Order the Pro Controll EZ Mount II now at rmioutdoorskc.com.